- Volume setting for each diver and tender to their individual comfort level
- Both divers can be set up on 4-Wire Mode or 2-Wire Mode or any combination of the two modes
- Ability to use both dynamic and preamplified diver microphones with a unique circuit that detects microphone type and automatically adjusts volume levels
- Weatherproof panel microphone for greater voice intelligibility
- Communicator can be left on charge indefinitely without damage to the batteries or communicator (/23 and /24 versions only)
- Communicator can be operated directly from the charger where AC power is available (/23 and /24 versions only)
Rechargeable with Internal Charger and Wireless Tender option: Part Number 2825A/24/28A Includes
- Hand-Held Push-to-Talk Microphone: Part Number 2405-28
- (1) 12 VDC Slide Terminal Gel-Cell Rechargeable Battery: Part Number 2890-05 - Expected life: 20 hrs
- Remote Wireless Kit: Part Number 2829-11 - Expected battery life: 4.5 hours in talk mode and 8 hours in recieve only mode.
- User Manual
- Power: 110/220VAC, 50/60Hz (automatic), or internal/external batteries 12VDC
- Frequency response: 300Hz to 12kHz
- Audio power output: 20 watts per channel
- Isolation transformer: Split bobbin medical grade
- Back-up battery: 1 ea. 12VDC, Gel-cell
- Expected battery life: 20 hours
- Dimensions: 9.0 in. H x 14.5 in. W x 10.0 in. D (22.9 cm H x 36.8 cm W x 25.4 cm D)
- Weight (approx): 22 lbs. (9.98kg)
All communicators will transfer topside noise to the diver when using the radio speaker only. To eliminate background noise and achieve clear concise communications, use a push-to-talk microphone or a headset or a remote walk & talk with a headset.
2 and 3 Year Extended Warranties are available for this product. Please refer to the Attachments tab for further information on the program and the Accessories tab to purchase them.
The Wireless Tender Option is a perfect complement to our 2-Diver and 3-Diver communicators. Amron's Full Duplex (Simulcom®) Wireless Tender is designed for the top-side tender to communicate to divers with hands-free operation and no required buttons to push. This wireless unit allows mobility for the tender while checking equipment and still maintaining constant contact with the divers (4 wire mode only).
Amron's Wireless Tender Option includes: (1) 2829-11 wireless headset and transceiver. Additional 2829-11 Wireless Headset and Transceiver Kits can be purchased for use with the Wireless Tender Option as "listen only" devices, as only one headset on the system can listen and talk priority to the divers. The design allows the capability to add an unlimited number of remote listen only headsets for the topside personnel. The units operate on 2.4 GHz up to a range of 120 yards (110 meters).
The transmitter/receiver unit is housed in a rugged plastic casing that can be clipped to a belt or slipped into a pocket. A single charge of the NiCad battery from the included AC adapter is capable of operating (transmitting and receiving) continually for up to 5 hours. In standby mode, battery will last for up to 8 hours. The standard headset is a tough over-the-ear single ear muff design with adjustable boom microphone. Also included is a smaller, lightweight headset/microphone for added mobility.
Depending on the age of the unit, existing non-wireless communicators in the field can be sent back for retrofitting. Contact your Amron Representative today to learn more!
2 and 3 Year Extended Warranties are available for this product. Please refer to the Documents Tab for further information on these programs.
Brand Amron International Communication Mode No Video No
Can you stack the banana plugs from the diver's communicators cable so you can have two divers on each diver channel?
Although it may be possible, we stronly discourage such operation. The added workload would cause overheating and stress to the amplifier card. Prolonged use in this condition will eventually cause perment damage and failure to the amplifier card.
When my battery does not appear to be holding a charge, how do I know if the problem is a bad battery or if the charger is broken?
To determine whether the problem is with the battery or charger you will need to verify if the charger is properly charging the battery.
Troubleshooting: Unplug your communicator and turn on the POWER switch. Measure the voltage across the yellow PUSH-TO-TALK (PTT) jack and write down this value for future reference. It should be greater than 9 Volts. Plug the communicator into an AC source and verify that the AC POWER LED on the front panel turns on. Re-measure the voltage across the PTT jack and note it down for future reference. It should be higher than the previous measurement. If this AC POWER LED does not light up when the communicator is plugged in, then check fuses F1 and F2 on the charger Printed Circuit Assembly (PCA). Allow the communicator to charge overnight. Unplug the communicator and re-measure the voltage across the PTT jack. If it is the same or less than the voltage you measured previously, then the charger is broken and the communicator needs to be sent in for repairs If it is the same or less than the voltage you measured previously, then the charger is broken and the communicator needs to be sent in for repairs. If the voltage higher than previous measurement but less than 13.5 Volts, then the battery is bad and needs to be replaced. If it is greater than 13.5 Volts but it still appears that the battery is not holding a charge, contact Amron for additional support. less than 13.5 Volts, then the battery is bad and needs to be replaced. If it is greater than 13.5 Volts but it still appears that the battery is not holding a charge, contact Amron for additional support.
Should I use a GFI when operating my radio off AC power?
When operating your Amron Diver Communicator on AC, it is critical to use a Ground Fault Circuit Interrupter (GFCI) or isolation transformer for tender and diver safety. Surges and spikes are common on AC lines found on ships, generated locally, or at the end of long extension cable runs and can exceed 1kVolt. Such surges and spikes can cause the fuses, F1 and F2, to blow on the battery charger board and in extreme cases damage the charger circuitry. The battery charger is designed so that such a failure will be isolated and will not cause a safety issue to the tender or divers. It is strongly advised that your Amron Diver Communicator be operated on an AC circuit with a high quality surge arrester or an AC isolation transformer.
How can I test for a blown fuse on my Amcom II series communicator?
If the unit is plugged into a live outlet and turning on the switch does not cause the AC POWER LED to light up, then the fuse(s) are probably blown. Unplug the unit from the outlet, remove the fuses and check continuity with a multimeter. Replace any fuse that does not show continuity.
How do I install a new microphone in my Amcom II Communicator?Please refer to the Panel Microphone Installation instructions located in the attachments tab.