- Exclusive 6 level light intensity dimmer touch pad
- Long lasting LED technology with 50,000 hour life
- Low profile design
- Adjustable integrated mounting plate
- 4-pin wiring configuration
- Low heat with high-performance heat sink
- Optional magnetic base available
- Optional red and blue lens filters
- Lamp type: Bright white LED
- Operating Voltage Range: 9-28 VDC
- Input Power: 15 Watts (maximum)
- Beam Angle: 120°
- Light Level: Adjustable up to 1000 lumens
- External Dimmer Control Voltage (7120 only): 0-10 Volts
- Housing: 6061 Aluminum
- Finish: Black Hard Anodized, MIL-A-8625, type III class 2
- Pressure Rating: 1000 fsw (300 msw)
- 7120 - 4-pin Marsh Marine: RMG-4-FS (not included)
- Delrin - Marsh Marine: G-FLS-D (not included)
- Stainless Steel - Marsh Marine: G-FLS-S (not included)
- Height: 2.6 inches (67 mm)
- Body Diameter: 3.3 inches (84 mm)
- Mounting Plate: 4.5 inches (114 mm)
- Weight: 1.50 lbs (0.68 kg)
*Mounting Holes - Industry Standard Two 0.25 inch (6.35 mm) diameter mounting holes with a 3.82 inch (97 mm) spacing.
Amron International's 7100 Series of LED Hyperbaric Chamber Lights provides industry leading illumination along with a dimmer feature not found on competitor's LED lights. The 7100 Series comes with an industry standard mounting plate to allow easy retrofit in existing chamber installations and an optional magnetic base that allows for quickly moving the light as needed. The light can be ordered with red or blue filters.
The 7120 comes with a 4-pin bulkhead connector. The fourth pin is a dimmer control line that controls the light level using a 0-10 Volts control line.The light level will be the higher of the internal and external dimmer control settings.
DISCLAIMER NOTICE: Amron's hyperbaric chamber light products are designed to be used in air chambers where oxygen concentrations remain below 23.5%. Our hyperbaric products (including external conditioning systems, internal conditioning systems, lights and other hyperbaric accessory items) are NOT designed for oxygen service, are not intrinsically safe, and do not meet the criteria given in NFPA-99, Chapter 20 and other applicable definitions. Use of our products in high-concentration Oxygen environments may result in serious injury and/or death.
Brand Amron International Video
What equipment will I need to install the 7100 Series Hyperbaric Chamber Light in my chamber?
The 7100 Series Hyperbaric Chamber Light and a 3- or 4- power cable with locking sleeve which is not included with the chamber light. Amron recommends the RMG-3-FS for the model 7100 Hyperbaric Chamber Light and the RMG-4-FS for the 7120 Hyperbaric Chamber Light. The standard RMG connector comes with an 18 inch pigtail but custom lengths are available. Also note, the standard RMG connector does not come standard with low smoke zero halogen cable, if you require this type of cable please let your sales representative know prior to placing your order. You will need a 4 conductor 18 AWG electrical penetrator to pass your power supply through the pressure boundary. When using the 7120 Hyperbaric Chamber Light with dimmer option, Amron recommends using a 0-10V dimmer controller. When using the 7100 Hyperbaric Chamber Light, Amron recommends using a standard household On/Off Switch. Both switches can be purchased at most hardware stores.
Can I replace the LED Light on the 7100 Series Hyperbaric Chamber Light?
Yes. Please refer to your user manual for instructions.
Does the 7100 Hyperbaric Chamber Light meet or exceed DNV standards?
Yes, but the light has not been third party tested and it does not come with any third party documentation.
Can I change the position of the light housing on the mounting plate of the 7100 Series LED Chamber Lights?
Yes, there are 8 screws under the integrated mounting plate that can be removed to allow you to reposition the housing on the mounting plate.
Does the Amron light come with an ASME PVHO-1-2012 certificate?
How does the light housing vent atmospheric pressure?
The 7100 Series Hyperbaric Chamber Light has a unique pressure vent that allows gas to pass in and out of the light housing.
Is the waterproof connector included with the light?
No, you will need to purchase a standard 3 or 4 pin RMG Waterproof connector. The 7100 series requires a three pin connector where the 7120 requires a 4 pin waterproof connector. You should also purchase the female locking sleeve to protect your waterproof connector from accidental disconnection.